Objective AI Report
Disclaimer: I am Medbidding AI. I am an unbiased AI robot. I have generated the following report automatically (without human intervention). The report was prepared by examining only the product images in the ad in detail. The report may contain errors. Medbidding and other parties disclaim any liability that may arise from this report or reliance on its contents. If you have any questions or notice an error in the report, please contact Medbidding engineers.
Report date: 24.03.2026
Report code: 1774335640
Elektro-mag M 420 BP Incubator Analysis Report
Device Identification and Basic Information
The product in the images is an incubator (oven) device used for temperature-controlled processes in laboratory environments. Based on the inscriptions on the device’s front control panel and outer lid, its brand has been identified as Elektro-mag, and its model as M 420 BP. The logos on the device, panel design, and overall craftsmanship quality indicate that the product is an original piece of laboratory equipment.
Areas of Use
The “INCUBATOR” inscription and temperature adjustment dials on the control panel indicate that the device is used for storing or cultivating samples at a specific temperature in microbiology, cell culture, medical analysis, and general laboratory applications.
Quantity Information
The images show 1 main device, 2 metal shelves inside the device, 1 power cable on the device, and 1 unidentified small plastic part.
Physical Condition and State
The device is in used condition. The outer casing is white, and the device is mounted on a black, curved floor stand. The upper outer surface of the device has superficial dirt, dust, and minor scratches. No dents, deep cracks, or deformations compromising structural integrity have been observed on the casing.
Mechanical and Internal Components
At the front of the device, there is a main outer door that opens with a gray latched handle. Behind the outer door, there is a transparent glass lid that isolates the inner chamber. There are no breaks or cracks in the glass lid. Inside the chamber, there are two perforated metal shelves used for placing samples. The shelves and the inner chamber appear clean and sturdy. The connection points and feet of the black bottom stand supporting the device are mechanically sound.
Electronic Components and Control Panel
On the left side of the device, there is a vertically positioned control panel. The electronic and mechanical components on the panel are as follows:
- Digital Display There is a green, 4-digit, 7-segment LED display. In the image, the screen is off, but the segment lines are visible.
- Membrane Keypad Below the screen, there are yellow directional and confirmation buttons. The buttons are labeled with letters A, B, C, D and functions “PROGRAM”, “DUTY”, “Select mode”, “Read set temp.”, “SET DOWN”, “SET UP”, “Stop timer”, “On”, “Off”.
- Safety Thermostat At the bottom of the panel, there is an analog adjustment knob (potentiometer) labeled “Safety thermostat”, scaled from 30 to 90 degrees.
- Warning Light Next to the thermostat knob, there is a red warning LED labeled “safety therm. takeover”.
- Power Switch At the very bottom of the panel, there is a green I/O (On/Off) power switch (POWER).
Labels and Technical Information
The following technical inscriptions and phrases are readable on the device’s control panel:
- M 420 BP
- programmable thermostat with timer
- Microprocessor controller with KTY type temperature sensor
- elektro-mag
- M 420 BP INCUBATOR
Accessories and Additional Parts
On the top of the device, a white power cable with a standard grounded plug is coiled. The cable has superficial dirt due to use. Additionally, on the ceiling of the device, there is a yellowish rectangular plastic piece with two square openings. It cannot be determined from the images whether this piece is a mounting accessory belonging to the device or an external part.
Potential Malfunction Risk and Evaluation
The images do not show any clear evidence of malfunction, such as a broken part, a severed cable, or burn marks that would prevent the device from operating. The inner chamber and glass lid are very well preserved. There is no noticeable risk other than superficial dirt on the outer surface of the power cable. The overall condition of the device is good for a used piece of laboratory equipment.
